The most prestigious law school admissions discussion board in the world.
|
 |
 
|
I'm gonna do a picket fence for my yard following this guy's Youtube video.
Poast new message in this thread
Date: June 18th, 2025 2:56 PM Author: impertinent location https://www.youtube.com/watch?v=3HCztbWyt2o
Hopefully this isn't too hard. Looks pretty straightforward though. I just don't want to spend $10k on a fence when I can do it myself for $1k. And then I'll know how to do a picket fence and I can start a fencing company (picket fences only) if AI takes my job. Thoughts? |
Date: June 18th, 2025 3:13 PM Author: Indecent charcoal area hell yeah (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49029008) |
 |
Date: June 18th, 2025 3:25 PM Author: vivacious dull plaza dragon (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49029037) |
|
Date: June 18th, 2025 3:30 PM Author: impertinent location (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49029053) |
|
Date: June 18th, 2025 3:31 PM Author: garnet bat shit crazy lodge i think u should paint yours tho, or at least waterproof stain it (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49029058) |
|
Date: June 18th, 2025 3:34 PM Author: impertinent location yea stain for sure (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49029063) |
|
Date: June 18th, 2025 3:47 PM Author: vivacious dull plaza dragon (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49029116) |
|
Date: June 20th, 2025 3:03 PM Author: overrated cobalt jew site Cr. And I prefer to paint everything first before you start installing. I like to put flex seal where ever any joints are.
Op remember that rot needs air and moisture. I didn't watch the video but paint your posts and put a little bit of gravel in the hole before sinking it. I've used plastic sheathing around the post where the ground layer comes into contact with it. That's almost always the rot point.
So far this year I have sunk 62 posts in my yard. An electric auger is about $150 on Amazon. Good luck. |
|
Date: June 20th, 2025 3:32 PM Author: impertinent location Ty I've done a lot more research since starting this thread on how to do it and line everything up.
I will take your advice and paint them before putting them in. Planning on gravel. Plastic sheath is also a good idea.
I have to do 24 posts. Currently there is a rotting fence that I need to take out. I might be able to use the holes that are in there now once I remove them (and will have to in a couple spots for the corners). Tho I think theyre only like 12 inches deep.
I was going to try a postdigger but got worn out just thinking about it. Will pick up an auger. |
|
Date: June 20th, 2025 3:45 PM Author: overrated cobalt jew site Do not go the post digger route. Those things are useless. It's like a teaspoon of dirt at a time. When digging holes have a pry bar for rocks and some hardy garden clippers for roots. You'll be pulling most of the dirt out with your hands. Id avoid the prior post spots at all costs. Stagger yours by a couple of feet.
Why gravel and not concrete? In my experience the gravel always fails. I pour concrete in dry and maybe do some mixing with water in the hole depending on soil moisture. Some people put nails in the bottom of the post to grab the concrete. I think it's a hassle. Buy extra 2x4s for the bracing. Digging a hole is like a mystery each time only what you find is never good. |
|
Date: June 20th, 2025 3:53 PM Author: contagious naked stag film My post hole digger is 180 it takes about 4 times and the hole is dug deep. Great for clay soil. Buried a dog with one even (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035469) |
|
Date: June 20th, 2025 4:26 PM Author: overrated cobalt jew site I have an electric one. A potato sized rock and it jerks me hard but still worth every penny. I dug a French drain with one. I paid $150. It's almost that much to rent a gas powered one man auger. One of my best purchases.
Edit: wait, like the two arm manual post digger? I use it because I don't always like bending over in a hole but fuck that for anything more than a couple of holes. |
|
Date: June 20th, 2025 4:24 PM Author: impertinent location OK. Auger it is. I'm just doing a bit of gravel on the bottom for draining and will use concrete to fill it up. (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035535) |
|
Date: June 20th, 2025 4:26 PM Author: overrated cobalt jew site Perfect (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035543) |
|
Date: June 20th, 2025 4:29 PM Author: overrated cobalt jew site This heavy-duty post hole digger with 1500W motor and 6" auger bit is perfect for fence posts, decks, and more. Others are loving it! https://a.co/d/7ruSzau (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035550) |
|
Date: June 20th, 2025 4:33 PM Author: impertinent location 180 I'll order this.
Thoughts on these 'postsavers' for the wrap where the post meets the ground? https://www.amazon.com/Postsaver-Protector-Guarantee-Dual-Layer-Protection/dp/B0CZ42D79Y/ |
|
Date: June 20th, 2025 4:40 PM Author: overrated cobalt jew site Yes, those wraps are definitely worth the money and effort. Posts always rot at the soil line. I also put flex seal where the rails meet the posts. Probably an overkill but I'm not planning on putting up a fence on my property again in my lifetime. (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035583) |
|
Date: June 19th, 2025 10:15 AM Author: impertinent location Any last thoughts and prayers before i start (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49031666) |
|
Date: June 20th, 2025 11:05 AM Author: impertinent location Subject: Question #1 Red cedar or pressure treated pine stained to look like red cedar (much cheaper)? (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49034662) |
|
Date: June 20th, 2025 3:10 PM Author: contagious naked stag film Pine (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035371) |
|
Date: June 20th, 2025 12:44 PM Author: impertinent location Subject: Question #2 Do I really need to set the posts below the frost line? Thats like 3 feet where I am. Will need to get a bunch of 4x4x8s and one foot of each will go to waste. I thought just 18-24 inches was fine. Have a hard time believing everyone in tristate area is not just doing 18-24 inches. (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49034919) |
|
Date: June 20th, 2025 3:09 PM Author: contagious naked stag film Yes or frost heaving will pwn your fence (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035369) |
|
Date: June 20th, 2025 3:33 PM Author: impertinent location (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035419) |
|
Date: June 20th, 2025 3:15 PM Author: overrated cobalt jew site Wow that's deep as fuck. For frost you want tho hole to be like an inverted funnel or like a bell shaped. That way when the ground freezes in pushes the post deep into the ground. Lots of concrete at the top means it will fail. Also, try and make the hole as small as practical. You want to disrupt as little soil as possible. More concrete is not the answer.
Run two string lines for the top and bottom of our posts and brace them with 2x4s as they set. I like to use the bottom rail for the prior post as the support for the next post. It gets your spacing down and it's one less side you have to brace. |
|
Date: June 20th, 2025 3:35 PM Author: impertinent location The official measure of the frost line by the county is more than what I am hearing the actual frost line is. I'm just gonna do the official measure anyway bc seems stupid to skimp on that now to save a few hours.
Good point re bell shaped I just watched a youtube vid on that. My area freezes over a lot in the winter.
Good tips man ty. |
|
Date: June 20th, 2025 3:47 PM Author: overrated cobalt jew site I know fence posts. It's literally my hobby. Take your time. It's going to look great and only you will see where it doesn't. (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035453) |
|
Date: June 20th, 2025 3:08 PM Author: Maniacal church building telephone great poast/moniker synergy (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035365) |
|
Date: June 20th, 2025 3:12 PM Author: Crusty station generalized bond (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035375) |
|
Date: June 21st, 2025 11:04 AM Author: Indecent charcoal area (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49037277) |
|
Date: June 20th, 2025 3:09 PM Author: contagious naked stag film Use black pine tar on the wood not stain, it will preserve it 1000x better, blocks UV and prevents mold & rot
https://www.youtube.com/watch?v=oqCuCgMxz3E
https://sagerestoration.com/products/black-pine-tar?srsltid=AfmBOoo73ZWAq3H4s_7JjE624iiT-9rhdImvHEwQH30BJHTaqgp1lwKL |
|
Date: June 20th, 2025 3:37 PM Author: impertinent location Ty. (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035430) |
|
Date: June 20th, 2025 3:26 PM Author: Slimy kitchen kitty I think you'll do a shit job because you're a jew lawyer. (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035403) |
|
Date: June 20th, 2025 4:29 PM Author: Opaque legal warrant people like this are basically neet, mgtow, fire, and good little sluts for gc all in one all while having a wife and kid. i honestly dont get the lifestyle. (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035552) |
|
Date: June 20th, 2025 4:33 PM Author: overrated cobalt jew site Fence builders? (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035561) |
|
Date: June 20th, 2025 4:35 PM Author: Opaque legal warrant its not the fence building. i respect diy people. its the fact that you can look at his back yard and think holy shit this whole place looks like a pita. also if hes a fence builder why doesnt he build a nice looking fence around the yard instead of that chain link bs. (http://www.autoadmit.com/thread.php?thread_id=5739961&forum_id=2#49035564) |